windows, ceilings, doors  
 • Main •
CEILINGS
the Ceiling
ceiling Whitewashing
Glutinous ceilings
Kleennye ceilings
Krashenye ceilings

others

 
WINDOWS
Advantage ON
Furnish of slopes
Of what consist ON
As establish ON
Gauging and installation ON

others

 
DOORS
Doors
Wooden doors
It is combined. Doors
Interroom doors
Sliding doors

other articles...

 
THE CARD

ru - ua - by - es - en - fr - de

 

the Pendant sliding door

It is a quite good choice for the modern house, where rooms small, and, so, walls in the big deficiency. Pass from kitchen in a dining room often connects two small premises. Therefore standard raspashnye doors here are inconvenient. Existing panel board doors can be easily altered in sliding if to use one of many accessible types of special adaptations. If apertures are wide enough, designs for folding doors opening in both parties will approach. New panel board doors for internal premises are on sale also. Adaptations are issued with all necessary accessories — by directing, pendular bolts, carriers, bottom directing, stoppers and screws. But arms for fastening directing should be bought separately. The lath is required to you to fix the directing. Before getting the adaptation for a sliding door, measure a door. The length of the directing should be twice more width of a door. The adaptation should correspond and weight of your door. If you use available door, close a lath of a quarter of a door box a little to reduce an aperture. It is better for definitive furnish and besides will protect from draughts. Remove a platband and a plinth at a wall along which the door will move, and then process this site of a wall. Installation comes to an end naveskoj accessories. And, at last, all design can be closed the special decorative panel. You can buy or make it.

a sliding door Design. in the design of a sliding door shown here carriers are attached from above to a door end face. In the bottom end face of a door along all its length the groove into which enters short bottom directing — "shoe" is cut. "Shoe" stabilises a door bottom edge at movement. Carriers are inserted into the pendular probes attached to plastic wheels, put on the top directing. The directing fastens arms to a basic lath. Stoppers on the ends limit a course of wheel blocks, and, means, and doors as a whole. The handle vrezana at a door.

the Pendant sliding door

sliding door Installation

1.

door Preparation. remove a door. Dismantle handles and loops. Choose a groove in the bottom end face of a door on the sizes specified by the manufacturer. Put a door on pair a trestle and note position of each carrier at the top end face of a door. SHilom do apertures in a tree, and then through cuts in carriers screw them on the top end face.

the Pendant sliding door

2. Fastening of a supporting lath. cut off a lath on the size specified by the manufacturer, and on 50 mm is longer than the directing. Put a lath on goats and drill directing apertures. Put a lath over an aperture. It should act from one edge for all length of a door. While the assistant holds a lath with level driven into the corner, you bore through apertures in those places where the lath will be definitively fixed. Clean a lath, dosverlite apertures and hammer into them in stoppers. Again put a lath and screw its screws of the suitable size.

the Pendant sliding door

3. How to hang the top directing. using utaplivaemye screws and self-fixed nuts, screw an arm on the directing. Arrange directing at a supporting lath. The centre of the directing should coincide with aperture edge, in a direction to which the door moves. The assistant holds directing, and you drill razmetochnye apertures in a lath according to apertures in arms. After fixing directing on a place insert into it on one wheel blocks.

the Pendant sliding door

4. How to hang a door. the assistant holds a door vertically under directing, and you move at this time wheel blocks along directing so that each block has risen opposite to the carrier. Slightly raise a door and on one push heads of bolts in a cut of carriers and slightly wind nuts on carriers. Line under a door wedges to fix it. Be convinced that the distance to a floor corresponds to the standard specified by the manufacturer. Adjust a door course, tighten nuts a key. Remove wedges.

the Pendant sliding door

5. Fastening of the bottom shoe. accurately translate a door in position "openly", having convinced thus that it does not come off the directing. Place a shoe on a floor by the aperture party. Check up, whether there is it under a groove in the bottom end face of a door. SHilom plan in a floor of an aperture and screw a shoe on a floor. If a floor stone, drill apertures a drill and hammer into them in stoppers.

the Pendant sliding door

6. Installation of stoppers. collect rubber stoppers and supporting plates completing screws. Push a stopper from each end of fixing of a course of a door directing to places. Then firmly twirl screws. So, stoppers on a place.

a source: Ural Mountains LTD



In addition on the given theme:

That such modern doors?
All about door loops
Choosing a steel door
Choosing a steel door - remember
Doors
the Doorbell
Wooden doors
Merits and demerits of a wooden door
How to choose interroom doors
How to choose a steel door